This write-up about how to make three Effortless Do-it-yourself Floating Photo Frames And How to Slash Plexiglass is sponsored by The Home Depot as part of the #THDProSpective System. It also has affiliate inbound links. See policies.
Straightforward Do-it-yourself photograph frames are basically a person of my most asked for tutorials and oddly sufficient, until finally now, I didn&rsquot have several to share!
.
I essentially created my father a massive Diy tailor made photograph frame as a Xmas reward a few a long time back and shared the tutorial for it right here. But it employed dowels, and a router, and it may have been a small far more associated than most people are wanting for.
So, in this article, I&rsquom heading to show you how I made three different fashion Super Quick Diy floating photograph frames with just two essential tools. navigate to these guys &rsquoll also demonstrate you how easy it is to reduce plexiglass for them, much too!
.
So if you&rsquore ready to get building, allow&rsquos go! I&rsquove bought the video tutorial in this article and the stage by step beneath:
Resources AND Products:
- Miter saw (or any wooden cutting saw is good&ndashdoesn&rsquot have to be a MITER saw)
- Nail Gun (optional, just makes matters more rapidly)
- Wooden Glue
- ¾&Key sq. dowels
- one×2 boards
- ¼&Primary x one ⅛&Key lattice trim
- Skinny Plexiglass Sheets
- Ryobi One+ HP Slash Off Instrument (used to minimize plexiglass)
- Clamps (also optional&ndashif you don&rsquot have clamps, you can use CA glue or painters tape in place of clamps to maintain parts even though wooden glue dries)
- Transform buttons
A Notice About FLOATING Photo Frames:
I&rsquom sharing how to make 3 various style FLOATING photograph frames in this tutorial, but the first step to earning any of them is chopping the plexiglass to the sizing you want.
.
If you don&rsquot want to use plexiglass for your frames, you can skip this action. But considering that the graphics/illustrations or photos I framed are &ldquofloating&rdquo within the body, they&rsquore generally sandwiched concerning two pieces of plexiglass. So plexiglass/acrylic is vital to be equipped to &ldquofloat&rdquo your photo.
.
To make items quick to change out in these frames, I also used these convert buttons&mdashor I phone them twisty tabs&ndashon the again to hold the plexiglass in put.  
HOW TO Minimize PLEXIGLASS
Usually, I have my area glass shop slash my glass and plexiglass parts for my projects.  But since these plexiglass parts will be tiny and numerous personalized sizes, it would be much much less expensive, faster and a lot easier to just slash them myself.
.
I used some (about) ⅛&rdquo acrylic sheets from Property Depot.  They appear in various measurements, all the way up to a 4×8 sheet.  I just grabbed some 11x14s.
I created some uncomplicated graphics on my pc (PicMonkey and Canva are terrific for this!) and also made use of a patch that I won a couple several years back at a convention for these frames.  You can use a image, a poster, material, what ever you want to frame for this.
.
I laid them out on my sheet how I appreciated the spacing, then marked exactly where I wished to cut&ndashno measurements below&hellipjust eyeballing how I imagined the spacing close to the impression seemed very good.
Now, I&rsquove utilised the low cost very little hand knife they claim will lower plexiglass in advance of and it was a horrible expertise with quite poor results.  I&rsquove also utilised a jig noticed to minimize plexiglass and it melts, receives trapped, then chips or cracks the sheet.
.
So THIS time, I tried out this new Ryobi One+ HP Compact Cut Off Instrument with a plastic chopping blade and was totally impressed with how quick and clean the cuts ended up.
When I very first saw this software, I discovered it kind of peculiar hunting.  But just after I made use of it, I comprehended the concept. 
.
It&rsquos fundamentally a hybrid concerning a drill and an angle grinder. It cuts like an angle grinder, but it feels a drill with the head turned 90 levels. 
.
It&rsquos compact and light-weight and it&rsquos acquired a ahead and reverse swap to turn the blade the two instructions.  It&rsquos also acquired a variable velocity bring about&mdashwhich is very good for slicing plastic to assist avert melting. 
It comes with a plastic and drywall blade, a metal lower off wheel, and a diamond blade for reducing tile and cement board.  You can understand far more about the new Ryboi A single+ HP cut off tool at the connection below if you&rsquore intrigued.
.
For reducing straight lines on the plexiglass, I just lined up a straight edge (scrap piece of wooden), clamped and ran the metal blade guard against it to make the slice.  You can skip the straight edge and freehand these cuts, as well if you have a constant hand. (I don&rsquot haha!)
I did discover it cut most effective in this scenario with the switch in reverse. It seemed to not melt that way.
.
I slice two pieces equivalent in dimensions for each and every merchandise I was framing. Then, I was all set to start building the real floating photograph frames.
Simple Do-it-yourself FLOATING Photo Body Style 1
Type 1 is my private favourite, so I&rsquoll get started with it 😊
This specific floating photo body design and style needs ¾&Prime square dowels and one×2 board. It is basically just a one×2 wrapped close to a square dowel body.
.
I employed ¾&rdquo square dowels for this and established up my miter observed to minimize 45 degrees.  Now, you don&rsquot have to miter these.  You can go away it on 90 and make butt joints.  You also don&rsquot require a MITER observed for this.  Any noticed that you can minimize rather straight with will perform fine.
.
I essentially trimmed four items of square dowel so that when suit alongside one another, they&rsquod be just barely (like ⅛&Prime) bigger than the plexiglass piece I was putting in it.
I utilized wooden glue to the corners and nailed them collectively with brad nails.  If you are client, and don&rsquot have a nail gun, just glue and clamp until eventually dry.
.
After the glue experienced dried, I reduce to suit one×2 pieces with 45 degree mitered corners all over this frame.  Again, butt joints are fine right here if you want to skip the mitered corners.
.
I glued and nailed these 1x2s about the edges leaving about ¼&rdquo sticking out the back again facet of the plexiglass, so that when I set up the two ⅛&Primary plexiglass pieces, it&rsquoll be flush across the back aspect of the frame.
Then, I screwed these twisty tabs into the back again sides of the body to hold the plexiglass in area.  I&rsquoll go back and clear the sawdust off the plexiglass later, but for now, I established this off to the aspect to make the future body.
Uncomplicated Do it yourself FLOATING Photograph FRAMES Model 2
Design and style two is a minor more simple and is manufactured of 1x2s and ¼&rdquo thick by 1 ⅛&Prime large lattice trim.
I began by cutting down the lattice parts so it would make a frame that the plexiglass would healthy Within.  All over again, just like just before, the mitered corners are optional.
After I experienced this lattice frame slice, I measured its overall dimension and reduce 1×2 parts to make a body whose total measurement matched that of the lattice body. See below 1×2 body laying on best of lattice body&ndashthey&rsquore the identical dimensions.
I glued and nailed the one×2 frame alongside one another and clamped right until dry. Once again, you can use super glue or painters tape if you don&rsquot have a nail gun or clamps 🙂
.
Then, I flipped it upside down and glued the lattice body on to the back again.  I used a hefty item to keep it in place until it was dry, then, I screwed twisty tabs on the back to keep the plexiglass in spot. 
Considering the fact that the lattice is ¼&rdquo thick, and the plexiglass is ⅛&rdquo thick, when the two plexiglass items are placed inside, all the things need to sit flush throughout the back again just like the last frame.
Again, I&rsquoll go back and thoroughly clean the sawdust off later, but for now, I moved on to the previous design frame.
Straightforward Do it yourself FLOATING Photograph Frame Model three
Design 3 is the exact same notion as type one, but in its place of working with 1x2s, I made use of ¼&Key x one ⅛&Key lattice trim to keep the body a small thinner and additional minimalist hunting.
So, I slice ¾&rdquo sq. dowels to make a body the identical dimensions or marginally bigger than the plexiglass I was framing and glued and nailed it alongside one another.
Then, I minimize lattice trim to wrap all around that body. 
I glued the lattice trim on so that there was about ¼&rdquo sticking off the back again facet of the sq. dowel body so that when the two pieces of ⅛&rdquo plexiglass are set up, it&rsquoll all be flush across the back.
.
I didn&rsquot have any brad nails short plenty of to nail this body on, so I simply just glued and clamped till it was dry.
If you don&rsquot have clamps, you can use painters tape to type of wrap all around the pieces to keep till the glue dries OR only use some super glue or CA glue to help maintain items in spot until the actual wooden glue is fixed.
.
Then, just like the final two frames, I put in twisty tabs to keep the plexiglass in put.
FLOATING Picture Body HANGING Options
The final action is clean up and hanging.  I made use of some glass cleaner to cleanse up all the noticed dust, then utilized a piece of double sided tape on the again plexiglass piece to make guaranteed the photos stay in spot, then set the frames back again jointly.
.
To cling, you can use your standard sawtooth hangers for this.
Or simply just area it on a shelf.
.
OR, use a drill to drill holes into the corners to run some paracord and cling it on a piece of wooden dowel you screwed into the wall.
As you can see, producing picture frames doesn&rsquot have to be challenging.  This is a terrific novice project you can tackle with negligible tools and get as inventive as you want. 
.
I essentially hung these graphics up in my desk spot to support continue to keep me enthusiastic even though performing by yourself from property suitable now. So, now that my desk area is comprehensive, I guess I must almost certainly get again to work 😊
I hope you&rsquove appreciated this small task.  There are a good deal far more coming your way, so be absolutely sure to subscribe to my e-newsletter underneath so you don&rsquot skip out on what&rsquos coming up coming!
.
And don&rsquot forget to pin this for afterwards!
Right up until next time, joyful constructing 😊