This publish about how to make three Uncomplicated Do-it-yourself Floating Image Frames And How to Lower Plexiglass is sponsored by The Property Depot as part of the #THDProSpective Method. It also consists of affiliate back links. See policies.
Effortless Do-it-yourself photo frames are really a single of my most asked for tutorials and oddly adequate, right up until now, I didn&rsquot have numerous to share!
.
I actually designed my dad a big Do it yourself customized image frame as a Christmas reward a few decades in the past and shared the tutorial for it here. But it made use of dowels, and a router, and it may have been a minor more concerned than most persons are wanting for.
So, in this write-up, I&rsquom heading to exhibit you how I designed 3 distinctive design Tremendous Easy Do-it-yourself floating photograph frames with just two essential tools. I&rsquoll also display you how quick it is to reduce plexiglass for them, way too!
.
So if you&rsquore all set to get developing, permit&rsquos go! I&rsquove obtained the movie tutorial listed here and the phase by step below:
Tools AND Supplies:
- Miter saw (or any wood chopping saw is good&ndashdoesn&rsquot have to be a MITER observed)
- Nail Gun (optional, just will make points faster)
- Wood Glue
- ¾&Primary sq. dowels
- 1×2 boards
- ¼&Primary x 1 ⅛&Primary lattice trim
- Skinny Plexiglass Sheets
- Ryobi 1+ HP Cut Off Software (made use of to slice plexiglass)
- Clamps (also optional&ndashif you don&rsquot have clamps, you can use CA glue or painters tape in place of clamps to hold parts though wooden glue dries)
- Convert buttons
A Notice About FLOATING Picture Frames:
I&rsquom sharing how to make three unique model FLOATING photo frames in this tutorial, but the 1st phase to building any of them is reducing the plexiglass to the dimension you want.
.
If you don&rsquot want to use plexiglass for your frames, you can skip this move. But because the graphics/photographs I framed are &ldquofloating&rdquo within the frame, they&rsquore fundamentally sandwiched concerning two parts of plexiglass. So plexiglass/acrylic is required to be able to &ldquofloat&rdquo your image.
.
To make matters quick to transform out in these frames, I also used these convert buttons&mdashor I connect with them twisty tabs&ndashon the again to keep the plexiglass in location.  
HOW TO Cut PLEXIGLASS
Generally, I have my neighborhood glass store slice my glass and plexiglass parts for my initiatives.  But since these plexiglass parts will be smaller and different custom measurements, it would be much less expensive, more rapidly and less difficult to just slash them myself.
.
I applied some (about) ⅛&rdquo acrylic sheets from Home Depot.  They arrive in many dimensions, all the way up to a 4×8 sheet.  I just grabbed some 11x14s.
I designed some straightforward graphics on my computer system (PicMonkey and Canva are excellent for this!) and also employed a patch that I gained a couple of a long time in the past at a conference for these frames.  You can use a photograph, a poster, fabric, whatsoever you want to frame for this.
.
I laid them out on my sheet how I appreciated the spacing, then marked in which I wished to lower&ndashno measurements here&hellipjust eyeballing how I thought the spacing all over the impression looked very good.
Now, I&rsquove employed the low cost minimal hand knife they claim will cut plexiglass right before and it was a terrible knowledge with incredibly inadequate results.  I&rsquove also utilised a jig saw to reduce plexiglass and it melts, receives caught, then chips or cracks the sheet.
.
So THIS time, I tried using this new Ryobi Just one+ HP Compact Cut Off Instrument with a plastic reducing blade and was completely amazed with how brief and clear the cuts ended up.
When I very first observed this software, I discovered it type of bizarre hunting.  But following I applied it, I understood the principle. 
.
It&rsquos generally a hybrid concerning a drill and an angle grinder. It cuts like an angle grinder, but it feels a drill with the head turned 90 levels. 
.
It&rsquos compact and light-weight and it&rsquos acquired a forward and reverse swap to convert the blade both of those instructions.  It&rsquos also acquired a variable pace set off&mdashwhich is good for slicing plastic to enable prevent melting. 
It comes with a plastic and drywall blade, a metallic minimize off wheel, and a diamond blade for cutting tile and cement board.  You can find out extra about the new Ryboi 1+ HP slash off software at the backlink below if you&rsquore intrigued.
.
For chopping straight strains on the plexiglass, I just lined up a straight edge (scrap piece of wooden), clamped and ran the metallic blade guard towards it to make the lower.  You can skip the straight edge and freehand these cuts, also if you have a continual hand. (I don&rsquot haha!)
I did discover it reduce ideal in this scenario with the change in reverse. It seemed to not melt that way.
.
I slice two items identical in measurement for every single product I was framing. Then, have a peek at these guys was completely ready to get started creating the real floating picture frames.
Simple Diy FLOATING Picture Frame Style 1
Model one is my personalized beloved, so I&rsquoll commence with it 😊
This particular floating photograph frame design and style involves ¾&Prime square dowels and 1×2 board. It is in essence just a one×2 wrapped about a square dowel frame.
.
I utilized ¾&rdquo sq. dowels for this and set up my miter observed to slice forty five degrees.  Now, you don&rsquot have to miter these.  You can depart it on 90 and make butt joints.  You also don&rsquot want a MITER observed for this.  Any saw that you can slice reasonably straight with will get the job done wonderful.
.
I mainly trimmed 4 items of sq. dowel so that when healthy with each other, they&rsquod be just scarcely (like ⅛&Key) even bigger than the plexiglass piece I was putting in it.
I utilized wood glue to the corners and nailed them jointly with brad nails.  If you are patient, and don&rsquot have a nail gun, only glue and clamp right until dry.
.
Following the glue experienced dried, I slice to healthy 1×2 pieces with forty five degree mitered corners all over this frame.  Once more, butt joints are wonderful here if you want to skip the mitered corners.
.
I glued and nailed these 1x2s all around the edges leaving about ¼&rdquo sticking out the back again aspect of the plexiglass, so that when I put in the two ⅛&Prime plexiglass parts, it&rsquoll be flush across the again facet of the frame.
Then, I screwed these twisty tabs into the back again sides of the frame to keep the plexiglass in spot.  I&rsquoll go back again and clear the sawdust off the plexiglass later on, but for now, I established this off to the facet to make the up coming body.
Easy Diy FLOATING Photograph FRAMES Design and style 2
Design 2 is a small easier and is produced of 1x2s and ¼&rdquo thick by one ⅛&Prime extensive lattice trim.
I started by chopping down the lattice pieces so it would make a body that the plexiglass would healthy Within.  Once more, just like ahead of, the mitered corners are optional.
The moment I had this lattice frame slash, I calculated its general size and minimize 1×2 pieces to make a body whose in general dimension matched that of the lattice frame. See under one×2 body laying on best of lattice frame&ndashthey&rsquore the similar dimensions.
I glued and nailed the one×2 body jointly and clamped right up until dry. Once again, you can use super glue or painters tape if you don&rsquot have a nail gun or clamps 🙂
.
Then, I flipped it upside down and glued the lattice body on to the back.  I used a large item to keep it in place until eventually it was dry, then, I screwed twisty tabs on the back to maintain the plexiglass in spot. 
Given that the lattice is ¼&rdquo thick, and the plexiglass is ⅛&rdquo thick, when the two plexiglass parts are placed inside, everything really should sit flush throughout the back just like the last body.
Once again, I&rsquoll go back and cleanse the sawdust off afterwards, but for now, I moved on to the past design and style frame.
Straightforward Do it yourself FLOATING Image Frame Fashion three
Type three is the exact same notion as fashion one, but alternatively of making use of 1x2s, I made use of ¼&Prime x one ⅛&Prime lattice trim to hold the frame a minor thinner and extra minimalist looking.
So, I slash ¾&rdquo sq. dowels to make a body the similar measurement or slightly greater than the plexiglass I was framing and glued and nailed it alongside one another.
Then, I lower lattice trim to wrap close to that frame. 
I glued the lattice trim on so that there was about ¼&rdquo sticking off the back side of the sq. dowel frame so that when the two pieces of ⅛&rdquo plexiglass are set up, it&rsquoll all be flush across the again.
.
I didn&rsquot have any brad nails small ample to nail this body on, so I merely glued and clamped right up until it was dry.
If you don&rsquot have clamps, you can use painters tape to variety of wrap all over the items to maintain until finally the glue dries OR only use some super glue or CA glue to support keep pieces in spot until finally the genuine wooden glue is fixed.
.
Then, just like the very last two frames, I put in twisty tabs to keep the plexiglass in put.
FLOATING Picture Frame HANGING Options
The remaining move is clear up and hanging.  I applied some glass cleaner to clear up all the observed dust, then utilized a piece of double sided tape on the back plexiglass piece to make sure the pictures continue to be in area, then set the frames back again collectively.
.
To hold, you can use your standard sawtooth hangers for this.
Or merely area it on a shelf.
.
OR, use a drill to drill holes into the corners to operate some paracord and dangle it on a piece of wooden dowel you screwed into the wall.
As you can see, creating image frames doesn&rsquot have to be intricate.  This is a great starter venture you can deal with with small equipment and get as innovative as you want. 
.
I in fact hung these graphics up in my desk spot to assistance retain me determined while functioning by yourself from house ideal now. So, now that my desk area is total, I guess I must likely get again to function 😊
I hope you&rsquove savored this tiny undertaking.  There are lots much more coming your way, so be confident to subscribe to my newsletter under so you don&rsquot overlook out on what&rsquos coming future!
.
And don&rsquot forget to pin this for afterwards!
Right until next time, delighted making 😊